The clevis connects to a pivot rod-and-ball assembly that consists of a rod that runs through a rubber pivot ball and slopes slightly uphill to the tailpiece of the stopper.
Pushing the knob and the lift rod down causes the pivot rod to push the stopper up; pulling the knob up causes the pivot rod to pull the stopper down. If you want to remove the assembly, you may be able to pull it right out. Or, you may have to twist it to unhook it from the clevis. This flange is screwed into the drain body, which is tightened to the underside of the sink bowl with a locknut.
The tailpiece, which may be fitted to a pop-up stopper, attaches to a drain trap by means of slip-joint couplings. The faucet supply hoses connect to the shutoff valves and faucet inlets, and you tighten them with adjustable pliers. They must have the right size connectors to fit, so it's worth checking before you buy the hoses. After connecting the pop-up stopper, the sink should be ready to use.follow link
How to Connect a Bathroom Sink Drain
Chris Deziel has a bachelor's degree in physics and a master's degree in humanities. Besides having an abiding interest in popular science, Deziel has been active in the building and home design trades since As a landscape builder, he helped establish two gardening companies. Skip to main content. Overview The supply, drain and vent pipes for the sink tie into the system of pipes already servicing your bathroom, and the difficulty of the rough-in depends on the system's overall configuration.
Installing the Pipes The locations of the supply and drain stub-outs are important. Preparing the Stub-Outs Before you hook up the sink, you need to install shutoff valves on the supply stub-outs. Connecting the Sink It's always easier to preinstall the faucet and drain onto a sink before installing the sink so you don't have to do these procedures while lying on your back. The specific size of the connectors should be included in the instructions for the specific faucet that you're installing.
You want to get lines that will have the appropriate ends for valve end and faucet end. Better to have extra long lines and have them loop.
No hard bends or kinks. Make them hand tight, and somewhere around a quarter to half turn with a wrench. The pop-up is the device that allows you to open and close the sink drain, usually made of a simple metal rod with ball attached to it. Drop stopped into sink from top, slide short end of rod into the opening on the tailpiece, making sure that the opening for the ball is facing toward the lever for the pop-up.
Install as per the instructions.
Bathroom Sink Plumbing
Slide nut to trap the ball in the tailpiece. Attach thumbscrew to pop-up lever rod while sliding the rod from the ball so they can attach and allow you to screw together. Seal your connections with silicone caulk. Finish with silicon around the top of the sink, anywhere that the basin of the sink meets the wall, filling any gaps with a thin bead of caulk. Let the caulk dry for about 24 hours before turning on the water and going back over your work to check for leaks.
Turn on the water and check for leaks. If you have small leaks from the rubber connections, try tightening more. The drain itself will also sometimes leak, which can be caused by over-tightening and straining the seal created by the connector gaskets. Try a new washer instead. It's also a good idea to check the gasket that goes under the tailpiece.
Try tightening the nut down more or try different washer or silicone.
Does the sink need to be connected to the vent in the wall? If so, how is that done? The tailpiece should be connected to the P-trap, which is connected to your drainage system. That will create the connection to the venting in the wall. Not Helpful 8 Helpful 6. No, not that I've ever seen. Most don't even have a manufacturer or model either.
Not Helpful 9 Helpful 5. These are for the sink's overflow. Not every sink has an overflow anymore, and most that do no longer plumb it in this fashion. Not Helpful 14 Helpful 6. When I turn on the water in the sink or flush the toilet in my master bath, I have a leak down in the basement.
Bathroom Sink Plumbing | Stuff to Buy | Pinterest | Bathroom sink plumbing, Plumbing and Bathroom
Do I need a new wax seal, and is the water from the sink on the same pipe? No, that's nothing to do with the toilet's wax seal, since the sink is causing the same result. You have a broken drain line or one of its fittings, shared by the toilet and sink. A wall and or ceiling below needs to be opened in order to find and permanently fix the break.
Not Helpful 8 Helpful 3. I don't want to install the pop-up that comes with the faucet set I'm about to install. Is there something I should do?
- Installing a new bathroom sink.
If using the same pipe, cap it off, and use a stopper in your sink. You can also use a new straight piece of pipe, but always check for leaks.
Want FREE Home Tips & Hacks?
Not Helpful 0 Helpful 0. If a spray nozzle hose that has a snap on connection comes apart, how does it go back together? Typically, you pull the collar on the hose end away from the end and release it once the nozzle's snap adapter is fully seated into the hose end. It may not have been installed correctly, and if someone just shoved the nozzle into the snap connector, then that's likely why it came off to begin with.
You have successfully subscribed! Thanks from the HomeTips Team.
You pull the collar back again to remove the nozzle. Not Helpful 7 Helpful 0. In that case, you would need to either call a plumber or get new valves at your local home improvement store to install yourself.
Related hook up bathroom sink plumbing
Copyright 2019 - All Right Reserved